The following Kreidezeit wall paints were tested by GRACO GmbH for suitability for the airless spraying process with GRACO spraying equipment:
Below is a list of the processing parameters found to be good as well as additional comments from GRACO GmbH.
The information serves the processor exclusively as an aid and refers only to devices of the company GRACO. Depending on the conditions at the construction site, the processing parameters may have to be adjusted by the local processor.
GRACO GmbH and KREIDEZEIT Naturfarben GmbH accept no liability for damage to equipment and in paintwork resulting from processing in accordance with these specifications.
Technical support for GRACO devices is available from the manufacturer:
GRACO Ltd.
Arnold summer field ring 2
D – 52499 Baesweiler
Tel: 0 800 – 180 00 76
Vega wall paint
Unit / Type: Umax II 795, Spray gun type: Contractor PC, Hose type: ¼, Whip: ¼, Nozzle system: Rac X + C6, High pressure filter / Mesh: 60M, Spray Gun filter / Mesh: 60M, Hose length: 15m
Experimental data
Nozzle Type | Diameter in mm | Diameter in inch | Litres/min | Spray pressure (bar) | thinner | Material °C | Spritzbild Rand/Strich | Auftrag Rate | Vertrag Struktur | Ergebnis gesamt | |
---|---|---|---|---|---|---|---|---|---|---|---|
LP 521 | 0,53 | 0,021 | 1,79 | <180 | 10 % | 20 °C | 2 | 2 | 1 | 2 | |
LP 519 | 0,48 | 0,019 | 1,47 | <180 | 10 % | 20 °C | 1 | 1 | 1 | 1 |
Result: 1 = very good, 5 = insufficient
Comment: Spray pattern very good with LP 519 especially for smooth surfaces, large surfaces with LP 521 in the crossway.
Casein Marble Paint
Device / Type: Umax II 795, Spray gun type: Contractor PC, Hose type: ¼, Whip: ¼, Nozzle system: Rac X, High pressure filter / Mesh: 60M, Spray gun filter / Mesh: 60M, Hose length: 15m
Experimental data
Nozzle Type | Diameter in mm | Diameterin inch | Litres/min | Spray pressure (bar) | thinner | Material °C | Spritzbild Rand/Strich | Auftrag Rate | Vertrag Struktur | Ergebnis gesamt | |
---|---|---|---|---|---|---|---|---|---|---|---|
LP 521 | 0,53 | 0,021 | 1,79 | <180 | 10 % | 20 °C | 2 | 2 | 1 | 2 | |
LP 519 | 0,48 | 0,019 | 1,47 | <180 | 10 % | 20 °C | 1 | 1 | 1 | 1 |
Result: 1 = very good, 5 = insufficient
Comment: Spray pattern very good with LP 519 especially for smooth surfaces, large surfaces with LP 521 in the crossway.
GekkkoSOL FINE-Grain
Experimental data
Nozzle Type | Diameter in mm | Diameter in inch | Litres/min | Spray pressure (bar) | thinner | Material °C | Spray pattern edge/line | Auftrag Rate | Vertrag Struktur | Ergebnis gesamt |
---|---|---|---|---|---|---|---|---|---|---|
HDA 545 | 1,14 | 0,045 | 8,23 | <110 | 10 % | 20 °C | 1 | 1 | 1 | 1 |
Device / Type: Mark X, Spray gun type: original, Hose type: ½, Whip: 3/8, Nozzle system: TMX, High pressure filter / Mesh: -, Spray gun filter / Mesh: -, Hose length: 15m
Tab.
Result: 1 = very good, 5 = insufficient
Comment: slight rebound of filling grain, very well suited for large areas, machine not under Mark V
Lime paint
Unit / Type: Umax II 795, Spray gun type: LL5, Hose type: ¼, Whip: ¼, Nozzle system: FFT + Rac 5, High pressure filter / mesh: 60M, Spray gun filter / mesh: 60M, hose length: 15m
Experimental data
Nozzle Type | Diameter in mm | Diameter in inch | Litres/min | Spray pressure (bar) | thinner | Material °C | Spritzbild Rand/Strich | Auftrag Rate | Vertrag Struktur | Ergebnis gesamt | |
---|---|---|---|---|---|---|---|---|---|---|---|
LL5 521 | 0,53 | 0,021 | 1,79 | <225 | 5 % | 20 °C | 1 | 1 | 1 | 1 | |
LL5 519 | 0,48 | 0,019 | 1,47 | <225 | 5 % | 20 °C | 1 | 1 | 1 | 1 | |
FFLP 314 | 0,36 | 0,014 | 0,74 | <225 | 5 % | 20 °C | 1 | 2 | 1 | 1 |
Result: 1 = very good, 5 = insufficient
Comment: When the paint is thinned by 5%, the spray pattern becomes very good and the edge area becomes very soft. If undiluted, strong edge coating
Lime paint -textured-
Device / Type: Mark X, Spray gun type: original, Hose type: ½, Whip: 3/8, Nozzle system: HDA, High pressure filter / Mesh: 60M, Spray gun filter / Mesh: 60M, Hose length: 15m
Experimental data
Nozzle Type | Diameter in mm | Diameter in inch | Litres/min | Spray pressure (bar) | thinner | Material °C | Spray pattern edge/line | Auftrag Rate | Vertrag Struktur | Ergebnis gesamt |
---|---|---|---|---|---|---|---|---|---|---|
HDA 545 | 1,14 | 0,045 | 8,23 | <160 | 10 % | 20 °C | 1 | 3 | 2 | 2 |
Result: 1 = very good, 5 = insufficient
Comment: TMX 541 nozzle is too small, blocked irregularly.
The tests were made on 05.04.2007.
Future product changes to machines and devices will invalidate the information.