Packing size 0,5 l Range 6 m² Consumption per m² 0,06 - 0,10 l Exact application rate values must be determined on site.
KREIDEZEIT Worktop Oil is a deep-penetrating, hard-wearing surface and solvent-free protector for countertops, tables and furniture of practically any type of wood – perfect for the kitchen and dining area. LFGB §31 tested. Also suitable for the treatment of wooden cutting boards, etc.
Suitable for the initial treatment and maintenance of untreated indoor wood surfaces. Can be tinted with KREIDEZEIT Pigments if desired.
Properties
Suitable for food contact (LFGB §31 tested)
Deep-penetrating
Saliva and sweat-resistant according to DIN 53160
Solvent and water-free
Very hard-wearing
Dirt and water repellent
Economical
Diffusible
Doesn’t crack, tear or peel
Easy to keep in good condition
Cobalt, lead and barium-free
Made from natural and renewable resources
Vegan
Full Declaration
Linseed oil, linseed stand oil, tung stand oil, castor stand oil, glycerol ester of wood rosin and manganese drier
When using the product, the complete Productinformation must be observed.
Warning! There is a risk of self-ignition when working materials are soaked with product.
Application Shake product briefly before application. Apply KREIDEZEIT Worktop Oil to untreated wood twice, allowing for drying between coats. The sub-strate may require sanding before applying the second coat. If using containers with different batch numbers, mix and stir together prior to application. The product must not be poured onto surfaces! Clean and dust down untreated substrates. KREIDEZEIT Worktop Oil comes ready-to-use and is applied undiluted.
1. Initial sanding Sand the wood (grit P80-100), rounding the edges. Do not use a finer sandpaper as this will make the wood too dense and unable to absorb enough oil. New, smooth, planed or finely pre-sanded wood should be rough sanded to ensure the oil can be absorbed. Dust down thoroughly after sanding.
2. First coat Apply KREIDEZEIT Worktop Oil evenly with a brush, cloth or sponge. After 10-20 minutes, thoroughly wipe the entire treated area with a dry, lint-free cloth until the surface has a uniform satin appear-ance.
Ensure that all unabsorbed oil has been completely removed, as otherwise shiny or sticky patches may remain. KREIDEZEIT Worktop Oil must fully penetrate into the wood. It must not form a layer on the wood.
To ensure good penetration on tannin-rich wood (such as oak), it is recommended to dilute the product with at least 10% Balsamic Turpentine (article no. 4301).
3. Re-sanding between coats (optional) Re-sanding between coats is only required if the surface has dried rough, for example if wood fibres have dried proud of the surface. Use sand paper (grit P100-120) in the direction of the fibre. Dust down thoroughly after sanding.
4. Second coat Repeat as per the first coat. 5. Wax treatment Not recommended for countertops.
Drying Time Dry and re-coatable at 20°C and 60% relative hu-midity after approx. 24 hours (48 hours for sub-strates containing tannin, e.g. oak, etc.). High humidity, cold temperatures and substrates containing tannin significantly extend the drying time. Suitable Tools Varnish brushes / flat brush, solvent-resistant sponges, cotton cloths and short pile rollers
Note Due to the content of natural oils, a yellowing occurs on surfaces with low exposure to light. A typical odour is emitted when natural oils dry; this disappears with time. Failure to remove iron filings on the surface can cause discolouration when applying the product. Not recommended for use on inside surfaces of cupboards; these are best treated with Shellac Varnish, Carnauba Wax Emulsion or Corfu Soap.
This product can be tinted with any KREIDEZEIT Pigment.
Start by stirring the pigments into a small amount of the product until it forms a lump-free paste, and then stir into the main mixture. Instruction The pigments can be mixed freely with each other. Colour samples are available from our retailers. Alternatively, the product can be tinted in any ratio with Stand Oil Paint -half rich-.
The online colour guides are for informational purposes only. We would like to point out that the color tones cannot always be displayed correctly by different monitors and their settings. The same applies to self-created prints of these colour charts. In order to get a better or true-to-original impression of our colours, we recommend the purchase of our colour chart, our colour guide with original coats or our printed, free flyers.
If there is no dealer in your region, you can order directly from us under +49 5060 – 6080650 or under info@kreidezeit.de. Please do not hesitate to contact us if you have any further questions.
