KREIDEZEIT Wood Hard Oil is a specialist oil for indoor use:
- on its own on highly absorbent types of wood such as spruce, pine and beech.
- as a hard-wearing finish on poorly-absorbent, dense wood after pre-treatment with Floor Hard Oil or Hard Oil
- for the protection of OSB and cork
Wood Hard Oil is particularly fast-drying, making it resilient very early on. It is our most durable and hard-wearing oil, offering very high water resistance.
Can be tinted with KREIDEZEIT Pigments if desired.
Kreidezeit Wood Hard Oil consists exclusively of natural oils and resins. It contains no ‘hidden’ alkyd resins produced from non-drying oils such as rapeseed, soybean or sunflower oil.
- Very hard-wearing, dirt and water-resistant
- Solvent-based, very economical
- Doesn’t tear or become brittle
- Diffusible, antistatic and warm to touch
- Transparent, honey-toned and colour-deepening
- Easy to work with and touch up
- Saliva and sweat-resistant according to DIN 53160
- Cobalt, lead and barium-free
Castor stand oil, tung stand oil, glycerol ester of wood rosin, balsamic turpentine and manganese drier
When using the product, the complete Productinformation must be observed.
Warning! There is a risk of self-ignition when working materials are soaked with product.
Shake product briefly before application.
Apply two coats of KREIDEZEIT Wood Hard Oil, allowing the first coat to dry before applying the second. The substrate may require sanding before applying the second coat.
If using containers with different batch numbers, mix and stir together prior to application. The product must not be poured onto surfaces!
Clean and dust down untreated substrates.
KREIDEZEIT Wood Hard Oil is ready for application undiluted.
1. Initial sanding
Sand the wood (grit P80-100), rounding the edges. Do not use a finer sandpaper as this will make the wood too dense and unable to absorb enough oil.
New, smooth, planed or finely pre-sanded wood should be rough sanded to ensure the oil can be absorbed.
Dust down thoroughly after sanding.
2. First coat
On poorly-absorbent, dense woods (such as oak and larch), apply the first coat with Floor Hard Oil or Hard Oil -solvent-free.
On more absorbent, coarser woods (such as pine, spruce and beech), proceed as follows.
a) Manual application Apply KREIDEZEIT Wood Hard Oil evenly with a brush, short-pile roller, cloth or sponge. After 5-10 minutes, thoroughly wipe the entire treated area with a dry, lint-free cloth until the surface has a uniform satin appearance.
b) Machine application Apply KREIDEZEIT Wood Hard Oil with a short-pile roller. After 5-10 minutes, thoroughly and quickly wipe the entire treated area with a soft pad until the surface has a uniform satin appearance. Change pad promptly once it becomes saturated. Long exposure times and working too slowly can cause the pads to bond.
Ensure that all unabsorbed oil has been completely removed, as otherwise shiny or sticky patches may remain.
KREIDEZEIT Wood Hard Oil must fully penetrate into the wood. It must not form a layer on the wood.
3. Re-sanding between coats (optional)
Re-sanding between coats is only required if the surface has dried rough, for example if wood fibres have dried proud of the surface. Use sand paper (grit P100-120) in the direction of the fibre.
Dust down thoroughly after sanding.
4. Second coat
Repeat as per the first coat.
5. Wax treatment
Oiled floors generally do not require wax treatment. To improve the gloss, you can finish with KREIDEZEIT Carnauba Wax Emulsion after at least 48 hours. To do this, dilute 1 part emulsion with 1 part water. Apply evenly and thinly, allow to dry and polish as needed.
Dust-dry after approx. 8 hours. Dry, sand and re-coat at 20°C and 60% relative humidity after approx. 24 hours (48 hours for substrates containing tannin, oak, etc.).
High humidity, cold temperatures and substrates containing tannin significantly extend the drying time.
Hardened after approx. 4 weeks. Use the surface gently and protect from water during this time.
Paint brush / flat brush, Short-pile roller (Magic felt, article no. 6517), Lint-free cloth, solvent-resistant synthetic sponges-
For larger areas: Floor machines with soft pads. Do not apply product with surface/ground scraper.
Cleaning the tools
Clean immediately after use with Balsamic Turpentine and then with Marseille Soap or Corfu Soap .
– Cleaning und care of oiled/waxed floors
– Instruction Applying Oils
Due to the content of natural oils, a yellowing occurs on surfaces with low exposure to light. A typical odour is emitted when natural oils dry; this disappears with time. Failure to remove iron filings on the surface can cause discolouration when applying the product. Not recommended for use on inside surfaces of cupboards; these are best treated with Shellac Varnish, Carnauba Wax Emulsion or Corfu Soap.
This product can be tinted with any KREIDEZEIT Pigment.
• Pigments in Oil
Start by stirring the pigments into a small amount of the product until it forms a lump-free paste, and then stir into the main mixture. Instruction
The pigments can be mixed freely with each other.
Colour samples are available from our retailers.
Alternatively, the product can be tinted in any ratio with Stand Oil Paint -half rich-.
We would like to point out that the color tones cannot always be displayed correctly by different monitors and their settings. The same applies to self-produced prints of these colours. In order to get a better or true-to-original impression of our colours, we recommend the purchase of our colour cards with original coats or our printed, free flyers.
If there is no dealer in your region, you can order directly from us under +49 5060 – 6080650 or under email@example.com.
Please do not hesitate to contact us if you have any further questions.