Wood Lazure in Wood Shades


Ready-to-use wood glazes in 9 classic wood shades for interior and exterior use.

SKU: 480.2 - 488.3 Category: Tag:

It comes ready to apply in 9 classic wood tints:



KREIDEZEIT Wood Lazure in Wood Shades is a diffusible, biocide-free protective coating for indoor and outdoor wood surfaces, such as windows, doors, wooden facades, timber frames, playground equipment, fences, garden furniture, car ports, beehives and much more.
KREIDEZEIT Wood Lazure does not crack, tear or peel. Rather, it gradually weathers and can be easily cleaned and restored.
The high-quality, expressive and completely non-fading earth pigments bring out the natural colour of the wood grain and provide a good level of UV protection.
Limited application on floors on request. Unsuitable for rough sawn wood, on old synthetic resin-based coatings and on roof surfaces.



  • Ready to apply
  • Dirt and water repellent
  • Doesn’t crack, tear or peel
  • Weather-resistant and elastic
  • Transparent, glossy and brings out the wood grain
  • Diffusible
  • Easy to keep in good condition
  • Saliva and sweat-resistant according to DIN 53160
  • Solvent-based (natural balsamic turpentine)
  • Free from biocides
  • Cobalt, lead and barium-free
  • Vegan


Full Declaration

Linseed oil, tung stand oil, linseed stand oil, balsamic turpentine, glycerol ester of wood rosin, earth pigments, iron oxide pigments, talc, clay, silica and manganese and calcium dryer

When using the product, the complete Productinformation must be observed.

Warning! There is a risk of self-ignition when working materials are soaked with product.

Preparing the substrate / Initial sanding
Remove any resin pockets and old synthetic resin-based coats. For outdoor use: soak any absorbent cutting edges and end grain areas with KREIDEZEIT Resin Oil and allow to dry for at least 24 hours.
Sand down new or weathered wood (grit P80-100), rounding the edges. Do not use a finer sandpaper as this will make the wood too dense and unable to absorb enough oil. New, smooth, planed or finely pre-sanded wood should be rough sanded to ensure the oil can be absorbed. Dust down thoroughly after sanding.

Do not prime new or regular absorbent wood. Only prime highly absorbent or weathered wood with KREIDEZEIT Base Oil.

Stir Wood Lazure thoroughly before and occasionally during application.
Apply Wood Lazure to untreated wood at least twice, allowing for drying between coats. The substrate may require sanding before applying the second coat.
If using containers with different batch numbers, mix and stir together prior to application. The product must not be poured onto surfaces!
Clean and dust down untreated substrates.
Apply KREIDEZEIT Wood Lazure undiluted.
Please note: wood in outdoor areas should be fitted with non-rusting metal screws and fittings, otherwise dark stains may appear after applying oil.

1. First coat
Outdoors Apply Wood Lazure evenly with a brush or pad. Avoid applying excess amounts or ensure to spread them thinly. Spread out any coalesced varnish from the corners using an unloaded brush.

Indoors Apply as above. Alternatively, if a glossy appearance is not desired, leave for 10-20 minutes before wiping the entire treated area with a dry, lint-free cloth until any remaining Wood Lazure is completely removed and a uniform satin appearance is achieved.

2. Re-sanding between coats (optional)
Re-sanding between coats is only required if the surface has dried rough, for example if wood fibres have dried proud of the surface. Sand using an abrasive cloth in the direction of the fibre. Dust down thoroughly after sanding.

3. Final coat
Repeat as per the first coat.
Especially if applying outdoors, it is important that the surfaces are well saturated once application is complete and a uniform silky-glossy appearance is achieved. Apply further coats of Wood Lazure if required.

Drying time
Dry and re-coatable at 20°C and 60% relative humidity after approx. 24 hours, or at least 48 hours for substrates containing tannin (e.g. oak).
High humidity, cold temperatures and substrates containing tannin significantly extend the drying time. Hardened after approx. 4 weeks.

Suitable Tools
Paint brushes and pads.
Do not use a spray or roller to apply the product.

Cleaning the Tools
Clean immediately after use with Balsamic Turpentine and then with Olive Care Soap or Corfu Soap.

Productinformation Wood Lazure Wood Shades

Material Safety Data Sheet Wood Lazure Wood Shades

Treatment of wooden windows
Application of Oils

to dealerlist

If there is no dealer in your region, you can order directly from us under +49 5060 – 6080650 or under info@kreidezeit.de.
Please do not hesitate to contact us if you have any further questions.